Maximizing solar power generation through conventional and digital MPPT techniques: a comparative analysis.

A substantial level of significance has been placed on renewable energy systems, especially photovoltaic (PV) systems, given the urgent global apprehensions regarding climate change and the need to cut carbon emissions. One of the main concerns in the field of PV is the ability to track power effectively over a range of factors. In the context of solar power extraction, this research paper performs a thorough comparative examination of ten controllers, including both conventional maximum power point tracking (MPPT) controllers and artificial intelligence (AI) controllers. Various factors, such as voltage, current, power, weather dependence, cost, complexity, response time, periodic tuning, stability, partial shading, and accuracy, are all intended to be evaluated by the study. It is aimed to provide insight into how well each controller performs in various circumstances by carefully examining these broad parameters. The main goal is to identify and recommend the best controller based on their performance. It is notified that, conventional techniques like INC, P&O, INC-PSO, P&O-PSO, achieved accuracies of 94.3, 97.6, 98.4, 99.6 respectively while AI based techniques Fuzzy-PSO, ANN, ANFIS, ANN-PSO, PSO, and FLC achieved accuracies of 98.6, 98, 98.6, 98.8, 98.2, 98 respectively. The results of this study add significantly to our knowledge of the applicability and effectiveness of both AI and traditional MPPT controllers, which will help the solar industry make well-informed choices when implementing solar energy systems.

A novel solution to optimal power flow problems using composite differential evolution integrating effective constrained handling techniques.

Optimal power flow is a complex and highly non-linear problem in which steady-state parameters are needed to find a network's efficient and economical operation. In addition, the difficulty of the Optimal power flow problem becomes enlarged when new constraints are added, and it is also a challenging task for the power system operator to solve the constrained Optimal power flow problems efficiently. Therefore, this paper presents a constrained composite differential evolution optimization algorithm to search for the optimum solution to Optimal power flow problems. In the last few decades, numerous evolutionary algorithm implementations have emerged due to their superiority in solving Optimal power flow problems while considering various objectives such as cost, emission, power loss, etc. evolutionary algorithms effectively explore the solution space unconstrainedly, often employing the static penalty function approach to address the constraints and find solutions for constrained Optimal power flow problems. It is a drawback that combining evolutionary algorithms and the penalty function approach requires several penalty parameters to search the feasible space and discard the infeasible solutions. The proposed a constrained composite differential evolution algorithm combines two effective constraint handling techniques, such as feasibility rule and ɛ constraint methods, to search in the feasible space. The proposed approaches are recognized on IEEE 30, 57, and 118-bus standard test systems considering 16 study events of single and multi-objective optimization functions. Ultimately, simulation results are examined and compared with the many recently published techniques of Optimal power flow solutions owing to show the usefulness and performance of the proposed a constrained composite differential evolution algorithm.

Managing the low carbon transition pathways through solid waste electricity.

The potential of solid waste as an energy source is clear, owing to its wide availability and renewable properties, which provide a critical answer for energy security. This can be especially effective in reducing the environmental impact of fossil fuels. Countries that rely heavily on coal should examine alternatives such as electricity from solid waste to provide a constant energy supply while also contributing to atmospheric restoration. In this regards, Low Emissions Analysis Platform (LEAP) is used for simulation the entire energy system in Pakistan and forecasted its capital cost and future CO2 emissions in relation to the use of renewable and fossil fuel resources under the different growth rates of solid waste projects like 20%, 30% and 40% for the study period 2023-2053. The results revealed that, 1402.97 TWh units of energy are generated to meet the total energy demand of 1193.93 TWh until 2053. The share of solid waste based electricity in total energy mix is increasing from a mere 0.81% in 2023 to around 9.44% by 2053 under the 20% growth rate, which then increase to 39.67% by 2053 under the 30% growth rate and further increases to 78.33% by 2053 under the 40% growth rate. It is suggested that 40% growth rate for solid waste based electricity projects is suitable for Pakistan until 2053 because under this condition, renewable sources contributes 95.2% and fossil fuels contributed 4.47% in the total energy mix of Pakistan. Hence, CO2 emissions are reduced from 148.26 million metric tons to 35.46 million metric tons until 2053 but capital cost is increased from 13.23 b$ in 2023 to 363.11 b$ by 2053.

Corrigendum: Unveiling the predictive power: a comprehensive study of machine learning model for anticipating chronic kidney disease.

[This corrects the article DOI: 10.3389/frai.2023.1339988.].

MPPT of PEM Fuel Cell Using PI-PD Controller Based on Golden Jackal Optimization Algorithm.

Subversive environmental impacts and limited amounts of conventional forms of energy necessitate the utilization of renewable energies (REs). Unfortunately, REs such as solar and wind energies are intermittent, so they should be stored in other forms to be used during their absence. One of the finest storage techniques for REs is based on hydrogen generation via an electrolyzer during abundance, then electricity generation by fuel cell (FC) during their absence. With reference to the advantages of the proton exchange membrane fuel cell (PEM-FC), this is preferred over other kinds of FCs. The output power of the PEM-FC is not constant, since it depends on hydrogen pressure, cell temperature, and electric load. Therefore, a maximum power point tracking (MPPT) system should be utilized with PEM-FC. The techniques previously utilized have some disadvantages, such as slowness of response and largeness of each oscillation, overshoot and undershoot, so this article addresses an innovative MPPT for PEM-FC using a consecutive controller made up of proportional-integral (PI) and proportional-derivative (PD) controllers whose gains are tuned via the golden jackal optimization algorithm (GJOA). Simulation results when applying the GJOA-PI-PD controller for MPPT of PEM-FC reveal its advantages over other approaches according to quickness of response, smallness of oscillations, and tininess of overshoot and undershoot. The overshoot resulting using the GJOA-PI-PD controller for MPPT of PEM-FC is smaller than that of perturb and observe, GJOA-PID, and GJOA-FOPID controllers by 98.26%, 86.30%, and 89.07%, respectively. Additionally, the fitness function resulting when using the GJOA-PI-PD controller for MPPT of PEM-FC is smaller than that of the aforementioned approaches by 93.95%, 87.17%, and 87.97%, respectively.

Proposal and Numerical Analysis of Organic/Sb2Se3 All-Thin-Film Tandem Solar Cell.

The low bandgap antimony selenide (Sb2Se3) and wide bandgap organic solar cell (OSC) can be considered suitable bottom and top subcells for use in tandem solar cells. Some properties of these complementary candidates are their non-toxicity and cost-affordability. In this current simulation study, a two-terminal organic/Sb2Se3 thin-film tandem is proposed and designed through TCAD device simulations. To validate the device simulator platform, two solar cells were selected for tandem design, and their experimental data were chosen for calibrating the models and parameters utilized in the simulations. The initial OSC has an active blend layer, whose optical bandgap is 1.72 eV, while the initial Sb2Se3 cell has a bandgap energy of 1.23 eV. The structures of the initial standalone top and bottom cells are ITO/PEDOT:PSS/DR3TSBDT:PC71BM/PFN/Al, and FTO/CdS/Sb2Se3/Spiro-OMeTAD/Au, while the recorded efficiencies of these individual cells are about 9.45% and 7.89%, respectively. The selected OSC employs polymer-based carrier transport layers, specifically PEDOT:PSS, an inherently conductive polymer, as an HTL, and PFN, a semiconducting polymer, as an ETL. The simulation is performed on the connected initial cells for two cases. The first case is for inverted (p-i-n)/(p-i-n) cells and the second is for the conventional (n-i-p)/(n-i-p) configuration. Both tandems are investigated in terms of the most important layer materials and parameters. After designing the current matching condition, the tandem PCEs are boosted to 21.52% and 19.14% for the inverted and conventional tandem cells, respectively. All TCAD device simulations are made by employing the Atlas device simulator given an illumination of AM1.5G (100 mW/cm2). This present study can offer design principles and valuable suggestions for eco-friendly solar cells made entirely of thin films, which can achieve flexibility for prospective use in wearable electronics.

Unveiling the predictive power: a comprehensive study of machine learning model for anticipating chronic kidney disease.

In today's modern era, chronic kidney disease stands as a significantly grave ailment that detrimentally impacts human life. This issue is progressively escalating in both developed and developing nations. Precise and timely identification of chronic kidney disease is imperative for the prevention and management of kidney failure. Historical methods of diagnosing chronic kidney disease have often been deemed unreliable on several fronts. To distinguish between healthy individuals and those afflicted by chronic kidney disease, dependable and effective non-invasive techniques such as machine learning models have been adopted. In our ongoing research, we employ various machine learning models, encompassing logistic regression, random forest, decision tree, k-nearest neighbor, and support vector machine utilizing four kernel functions (linear, Laplacian, Bessel, and radial basis kernels), to forecast chronic kidney disease. The dataset used constitutes records from a case-control study involving chronic kidney disease patients in district Buner, Khyber Pakhtunkhwa, Pakistan. For comparative evaluation of the models in terms of classification and accuracy, diverse performance metrics, including accuracy, Brier score, sensitivity, Youden's index, and F1 score, were computed.